Will Hypertech tuning void my warranty?
No. Federal law prohibits a dealer from voiding your warranty just because you are using
aftermarket parts, with only two exceptions: A warranty claim can be denied only if the part
is the cause of damage, or if it adversely affects the emissions or the emissions system.
Go to SEMA ACTION NETWORK for more information on consumer rights.
Return to top of page
What is Hypertech Power Tuning?
Power Tuning is the optimization of the fuel delivery and ignition spark timing curves to
produce maximum horsepower and torque. An engine's air, fuel and spark requirements vary
throughout its operating range. When Hypertech's engineers and technicians develop Power Tuning
for a vehicle, their objective is to absolutely nail the best spark timing and the best air/fuel
ratio for every point in the rpm curve.
Return to top of page
Is Hypertech Power Tuning emissions legal?
All Hypertech Power Tuning products are legal for sale or use on California pollution-controlled
motor vehicles according to CARB Executive Orders. Power Tuning products for 1998-2003 Ford and Chrysler gasoline,
as well as Dodge Cummins diesel applications are currently in approval-pending status, based on completion of required
testing presently being conducted. All 2003 and prior Ford Power Stroke and all GM Duramax applications are legal for
sale or use on California pollution-controlled motor vehicles under CARB E.O. D-260-10 and D-260-11, respectively.
Return to top of page
How does Hypertech develop a Power Tuning Program?
Tuning an engine is an empirical process that requires sophisticated equipment and knowledgeable
technicians to produce "real world" results. Power tuning is a time-consuming and expensive procedure
that requires running the engine on a dyno, testing at each of the tuning points in the computer's
"lookup table", and developing new values for best spark timing and fuel delivery. This is the
procedure used by the automobile manufacturers, and it is the procedure we use exclusively.
We use two computerized chassis dynamometers at our Engineering Center in Memphis to develop the
most powerful tuning programs possible. First our engineers experimentally adjust the spark timing
to obtain the highest torque and power readings at a given engine rpm. Then they adjust the air/fuel
ratio to obtain the highest possible power and torque readings that an optimized air/fuel mixture can
produce. After the spark timing and air/fuel ratio for that particular engine speed have been optimized,
the rpm is increased to the next point and the entire procedure is repeated again. The process continues,
point by point, up to the engine's maximum speed. This technique is called experimental, point-by-point
curve fitting. There is no more effective way to power tune an engine.
Return to top of page
How does Hypertech validate a Power Tuning Program?
When we select a vehicle for Power Tuning development, we tune a number of vehicles
so that our engineers can establish a bell curve. For example, if you had 100
stock vehicles and tested them on a track or a dyno under the exact same conditions,
you would find that most had about the same power. Some would be slightly less
powerful and some would be slightly more powerful. Plotting the results on a
graph would produce a bell-shaped curve. Therefore Hypertech engineers always
test enough vehicles to know that we are in the middle of the bell curve, and
that the results are typical of the majority of similar vehicles. After we develop
a Power Tuning program on the dynamometer, the next step is a "beta" test where
we install the tuning in dozens of test vehicles for "real world" road testing
and evaluation. We receive detailed reports on how the tuning program performs.
If our beta testing confirm our dyno results, then and only then do we release
the new tuning program. Return to top of page
Why don't factories optimize their engines tuning?
The factories tune for average drivers who might buy low-octane gasoline and
lug the engine. Hypertech Power Tuning is designed for drivers who care about
performance and use premium-grade fuel. With the rising cost of gasoline, Hypertech
now offers special 93/87 octane "Dual Fuel" programs for selected cars and trucks
with low-compression engines that are designed to run on regular octane gasoline.
We have tested a few engines where the factories have left very little gains
to be made. But we were still able to optimize the tuning curve to gain some
additional horsepower and with all the other performance features available
in the Power Programmer, our customers believe the Power Programmer is an excellent
value. In general, we find that the factories do not optimize the spark curve
at low speeds or extremely high speeds nearly as well as they do in the 2000
to 4000 rpm range. Our engineers often find that engines require additional
spark advance at low speeds and very high speeds for optimum performance. There
is no rule of thumb, however, which is why we must evaluate and dyno test specific
engines and vehicles. Return to top of page
Can I run regular gasoline?
While most tuning is designed and calibrated for 92 or 93 octane fuel, we do
have some applications that have a dual fuel tuning program available. Please
check our GM or Ford
Feature Comparison Chart for specific applications. Return to top of page
Will Power Tuning hurt my engine in any way?
No. Best power is always made when air/fuel ratio and the spark tuning has been optimized for maximum power,
meaning maximum "push" on the piston during each power stroke. Damage occurs if the air/fuel mixture
is too lean, meaning that there is not enough fuel for the amount of air in the cylinder. This results in excess
super heated air which can cause burning of valves and pistons and will also induce detonation (which can break
pistons, etc.) Relative to spark timing, too much "advance" will cause detonation which reduces power
and can also damage parts exactly as a lean mixture does. When we finish power tuning, your engine will run at
maximum efficiency yet safely distanced from possible damage due to leanness or excessive spark advance.
Return to top of page
Does Power Tuning work with modified vehicles?
Hypertech Power Tuning is calibrated for stock or near-stock engines (engines equipped with high-flow air filters
and cat-back exhaust systems). Any additional modifications that alter the engine's airflow and volumetric efficiency,
such as installing a modified mass airflow sensor, high-lift or long-duration camshaft,ported heads, headers,
supercharger, nitrous oxide, etc., would require new tuning. This tuning must be done individually on a dynamometer
with a vehicle equipped with those parts. If you have modified your engine with aftermarket equipment other than a
low-restriction air filter or cat-back exhaust, the Power Tuning developed for a stock engine may not be correct.
Note that the Power Programmer III provides many additional benefits beyond Power Tuning. Depending on the application,
you can adjust the engine's rev limiter, raise the top speed limiter to match the speed rating of factory-approved tires,
adjust the transmission shift points and shift firmness, correct the speedometer and odometer readings for non-stock tires
and rearend gear ratios, and adjust the on/off temperature for electric cooling fans. That's why we say that a Hypertech
Power Programmer III is the most powerful performance product an enthusiast can own!
Return to top of page
How does Hypertech Power Tuning change the way my engine performs?
Hypertech tuning replaces stock computer tuning inside the vehicle's computer to give maximum power and torque.
The tuning can be delivered in the form of a chip that replaces the stock computer chip, a chip that piggy-backs the
stock computer chip, a chip that plugs into the back of the stock computer, or a device that reprograms the stock computer
with Hypertech Power Tuning. The type of device needed is dictated by the type of computer in your vehicle. The tuning
information is stored in the computer chip which controls all of the engine's characteristics like air/fuel ratio, spark
advance, shift firmness, shift points, top speed, rev limit, and axle ratio. Sensors monitor many engine and transmission
parameters like RPM, manifold air pressure, mass air flow, coolant temperature, intake air temperature and many more.
These sensors send this information to the computer. The computer uses this information delivered from the sensors along
with the information stored on the chip to deliver the optimum air/fuel ratio, spark timing, shift firmness, etc. for this
set of operating conditions at that instant in time. Hypertech can tune a vehicle for the conditions by using a dynamometer
to measure horsepower output while altering the information stored on the chip. This is how Hypertech maximizes your vehicle's
power output!
Return to top of page
How will Hypertech Power Tuning affect my gas mileage?
Hypertech Power Tuning does not alter part-throttle calibrations in any way that would hurt fuel economy. Only high-load
calibrations are modified for maximum power and torque. Fuel economy will remain virtually the same or may even improve
(depending upon specific driving patterns) unless the vehicle is driven in a spirited manner or is regularly used for towing.
For trucks that tow, Hypertech's Power Tuning is generally closer to the best fuel economy than the stock tuning. So in addition
to power gains, a vehicle that tows with Power Tuning will often exhibit better mileage than one with stock tuning.
Return to top of page
Does Hypertech Power Tuning remove the speed and rev limiters?
It depends on the specific vehicle. On most chips, we raise the top speed limiter to give a maximum speed of 2 MPH less than
the speed rating of the stock tires (i.e. if the speed rating of the stock tires was 130 MPH we would set the limiter to 128 MPH).
The rev limiter is raised when possible and is completely dependent on the application. The Power Programmer III,
available for 1994-97 LT1 and LT4 cars and 1996-2001 Vortec Trucks, allows the user to set the top speed limit to match the
speed rating of the tires that have been installed on the vehicle. It also allows the user to alter the rev limiter within a
predetermined range.
Return to top of page
What if a dealership re-flashes my vehicle's computer and I had not previously taken it back to stock?
When a dealership or service facility re-flashes a computer (sometimes to install a new OEM calibration), the Hypertech tuning will be erased and your Power Programmer
will not work. Once your vehicle has been tuned, the stock calibration is the only information contained in the Power Programmer. When this occurs and you attempt to use
it again, an error code will appear. The Power Programmer must then be sent to Hypertech to remove the existing stock calibration and reinstall Hypertech tuning. It may
take up to two weeks for Hypertech to provide and complete this service. All returned units should be sent freight prepaid, following the instructions obtained from
Hypertech Technical Sales Staff at 901-392-8888. ( See Hypertech Instruction Manual under "Calibration Not Found" section.)
Return to top of page
I returned my vehicle back to stock before I took it to the dealership. After the dealership re-flashed
my vehicle's computer, the Power Programmer doesn't work and I got an error code. Why?
If the Power Programmer (or HyperPAC) doesn't contain this new calibration, you will not be able to re-install the tuning and the unit must be returned to Hypertech
for updating. The unit will not allow the tuning to be installed automatically, if we have not tested the new calibration that was installed in your vehicle's computer
by the dealership or service facility. What did happen is that the Hypertech Power Programmer downloaded a copy of the new calibration, causing it to display an error
code. Once the unit is returned to Hypertech it will be sent to engineering to download and process the new OEM calibration information. It may take up to two weeks for
Hypertech to provide and complete this service. All returned units should be sent freight prepaid, following instructions obtained from Hypertech Technical Sales Staff
at 901-382-8888. (See Hypertech Instruction Manual under "Calibration Not Found" section.)
Return to top of page
Does Hypertech stand behind its advertised results?
Absolutely! We select typical tests for publication. We conduct consecutive tests to stabilize the engine operating conditions
and we perform all tests at the same oil and coolant temperatures to obtain repeatable results. We require at least three
consecutive tests with a variance of no more than one or two horsepower before we accept the results as accurate and reproducible.
Due to differences among individual vehicles, a particular engine may make more or less horsepower than our published results.
Please note that except for certain "Dual Fuel" applications for selected trucks, all Power Tuning is based on the use of premium fuel.
Use of regular grade or low-octane gasoline (less than 93) will result in no horsepower gain.
Return to top of page
Why are there three stages of power tuning for the diesel engines and why do you recommend using the transmission feature?
Diesels, under heavy loads and for long periods of time, can build up excessive internal heat in engines and transmissions.
When that occurs, the check engine light may come on, or flash off and on to warn you that you need to either back off on the power
level, or lighten your load. You can't always lighten your load, but now with the Hypertech Power Programmer, you can select the maximum
power tuning stack you can safely use under those particular conditions. Why should you use the transmission feature? The transmission feature allows the automatic transmission's shift firmness for increased
line pressure. This option should be utilized when other than stock tuning is in the vehicle. At high boost levels with higher
torque, the transmission needs to have firmer shifts...this helps to keep the clutch plates in the automatic transmission from slipping.
This is especially true when towing heavy loads. For everyday use, it isn't as critical.
Return to top of page
